@AYHAN-YILDIZ just ansered to your post on the same topic in the V2 thread. No need to post this multiple times. I recommenc closing the duplicate.

@AYHAN-YILDIZ said in Suunto Vertical 2 General Discussion: Hello everyone, I just learned that on the Suunto Vertical 2, manual SpO₂ measurement via the widget is no longer available. The feature has been restricted by software, reportedly for battery life reasons, and now SpO₂ measurements are only taken automatically during sleep. This information has been confirmed by four different Suunto specialists. I find this very disappointing, especially for a flagship device that is meant to support outdoor and high-altitude activities, where real-time SpO₂ monitoring is often crucial. I’m curious to hear your thoughts on this restriction. How do you feel about a flagship watch limiting such a core health and performance feature? While I disagree that this is a core health and performance feature, for me it is still there to be enabled from the widget. Can you show a picture of how your widget looks like?

@pavel.samokha STEPS motor system provides power assist and the Di2 technology handles the gear changes.

For the record, I think the Race 2 and Vertical 2 faces are very good, I’d like to see more development in terms of options for those two. For example being able to configure the Race 2 graph to show us sleep over time, or HRV, or CTL, or cycle through all three if you tap on it. The same with the Vertical 2, make the bottom complication configurable too! Oh and larger complication fonts

@GiPFELKiND said in Suddenly while bike riding Connection HR Belt broken: But why should the hr Monitor signal get lost? I have no idea. I was just responding to @2b2bff’s comment about the HR graph. I will say that I have also been experiencing external HR drops on both the 9PP and V1 running the latest firmware. But usually it just drops for a few seconds at most, and never completely loses connection like it seems yours did. I’ve also been wearing an original 9P running super old firmware (2.26.8) and have not experienced any external sensor drops on it. So I’d guess it’s firmware related and hope that it gets fixed with the Q4 update.

@Kristin-Jensen Oh, no, please, not smaller! In fact I would prefer bigger!!

Seems Suunto has a twisted sense of humor.

@PetrMisek But if you look, the graph perfectly shows the problem. One could think, not knowing, that you slept from midnight until 5 PM the next day. It is not helpful at all. Also, why does the axis show 120 percent? Is this another bug by Suunto? And then again, right after the activity, there is a rapid rise in the resources.

@Stavrogin Re “Not sure what I am saying yes to”. You weren’t saying “Yes” there in my reply. I was, in acknowledgment that you were showing the app I had suggested initially but not understanding (“?”) why you were directing the post at me. I didn’t suggest the sport profile. Perhaps @leehikes was your intended recipient?

It happened to me during a run I did a really slow jog with a partner from my office that runs much slower than I normally do. In the end of the run the pace went down and I believe my HR went down to the 90s. It was cool outside (8-9C) and I didn’t sweat much. Really very relaxed run. On asphalt, including during stops at traffic lights, my HR recording jumped to about double my actual HR which is about 20bpm above my max of 165bpm…[image: 1765170003392-1000122270.png]

@2b2bff I’d be surprised to see a tilted rectangular display But I agree on the QC part.

@Manuel-Extreme Thanks for the follow-up, this gives me some hope. The obvious question is whether or not the new watch acts the same as the one returned, or is it like you expect, i.e. no OHR disconnect. Thanks again.

@sky-runner Totally agree. I like Coros, but it has been even more obvious with some of the folks they pay to review their watches.

@Egika ok thanks for answer, I remember that I had similar problem maybe last winter with SV1, I am not sure if there was some update on not

@mando funny I thought that the torch was a gimmick and now find myself using it all the time! I find the V2 easier to read than the V1. Display is lovely and clear.

![alt text](image url[image: 1763766353905-1000011223.png] In Android it is useless just now unless you press edit. If it is fixed in the next update that will be most appreciated.

@prashant sleep and resources and HRV work great for me and like I said are inline with other devices I wore simultaneously with my Suuntos.

@SteffMG76 Hi. I’m m still not sure what you mean or why you would need to adjust that reading. I’m more interested in change over time than in a specific value. I can’t adjust the barometric pressure reading on my Coros but I can adjust the altitude (and handily I can do this mid exercise to recalibrate height at a known point). Where would you get a reference atmospheric pressure value from to set your watch to? And how would you know that value is correct for your location? Genuine questions as I’m interested in why you might want to do this.