@Marcin-Byrtek yeah right, default is on, but what if you got your Vertical used or tested by someone (like mine) and wasn’t set up by you?
Maybe I could reset at some point my watch to see how is the default ON state 🙂

@suunto867 said in RESOLVED: Movescount and device settings out of sync. Please synchronize your Suunto Ambit3 Peak now!:

It seems not very intuitive to have to force the sync from the watch while plugged into the USB.

Did you made those Movescount changes while your watch was plugged in? Or perhaps you didn’t have internet connection at that moment you plugged in your watch? Or was your firewall concerned about Moveslink2 making connections?

There’s no active connection, polling from Moveslink2 side or pushing setting updates from Movescount. Thus Moveslink2 application starts it chat with Movescount service only after you’ve connected your watch to USB and it has synced data from the watch, it then checks just once with MC if there’s anything new to send to the watch. So you either make your Movescount changes before connecting to usb, reconnect your watch to trigger new sync or force sync manually. You also might just had a random glitch or there was some short term issue at Movescount side.

Autosync option in the watch menu only affects syncing with mobile app.

Thx both for the tips!

@isazi Thanks for the advice. Got back my old cable and it worked. The thing is that this old cable’s clip broke and i have to hold and press the watch against it while synchronizing. The new cable is form Suunto and just started malfunctioning. Going to see if warranty applies.

@Timbo , ummm… in most cases I would avoid “Suunto” and “open” in the same sentence 🙂

Are you aware of https://www.suunto.com/Content-pages/digital-service-transition/?setcountry=en ? The future of those apps and pretty much anything related to Movescount is not exactly clear at the moment.

@Fenr1r exactly. this one was about Ambit2

@Steradiant no I don’t think it’s possible. The best thing todo is just manually pause.

It makes browsers to complain about Cross-Origin Resource Sharing, once this is addressed, Mapquest service responds with:
The AppKey submitted with this request is invalid.

In others words, not much end users can do about it.

@Olli2709 I would have service do this, you could ruin the watch seal or worse.

@klaus-0 these threads may help you
https://forum.suunto.com/topic/520/additional-external-tools
https://forum.suunto.com/topic/5381/what-is-your-workflow
https://forum.suunto.com/topic/3438/suunto-cable-operated-software-alternatives?_=1611052107367

@jeromep
You can try via chat too.
Suunto support usually replies.

@zoran-markovic said in Suunto 3 and apps:

Wrong subcategory, should be Android

Not really - none of it goes through mobile app, just Movescount.com + Suuntolink.

@vinko-miketek please read here https://www.suunto.com/Support/faq-articles/transition/how-do-i-use-the-suunto-services-with-ambit2/
And after you setup Suunto App you can connect your account with your Strava account, then when you sync your watches using SuuntoLink your activities will be uploaded to Strava

@aksta70 said in Smart sensor belt fault:

Smart sensor belt does not seem to pick up correct heart rate or sometimes nothing at all. Belt is about a year old. Is there a shelf life for these? The belt has been washed, I wet the patches before use and new battery in the sensor itself but still not working

It is the one with movesense area in black or grey?

@mvpereira I used a Polar OH1+ (which is fundamentally the same as the Verity) by wearing it on the same wrist as the Ambit3 and found that the signal travelled 2-3cm under water and thus the connection remained if I wore them close enough together.

I’m now using a Fenix 3 on which Garmin have disabled recording of HR when swimming and I use the OH1 in recording mode, export the file from Polar Flow after the swim and then add it to my swim workout in TrainingPeaks - TrainingPeaks then combines the HR and the swim details from the Fenix 3.

Either option should work for the Ambit3.

Bringing this issue up in case it can be reported for fix in SA android.

Here’s the screenshot from the Vertical where it shows okay vs my A3P with the display issue, wore both watches during the same session.

Thx

SmartSelect_20231222_171155_Gallery.jpg

SmartSelect_20231222_171130_Gallery.jpg

@andrasveres supplier needs Todo that usually

@dmytro said in Suuntolink as ios/android app?:

but I would bet on some hardware limitations, otherwise ambits could be completely supported by SA and suunto wouldn’t need to develop suuntolink 4.0 update in the first place.

That would still leave A1 & A2 out in the cold. The idea is to cover maximum number of legacy devices to at least some extent while keeping workhours and other resources to a minimum. And all pre-9P & -7 watches still need a maintained desktop solution to handle firmware updates, so it kind of makes sense to pack it all into Suuntolink.

Instead of asking for a Suuntolink mobile port, that request should really read “full Suunto App support for all Bluetooth-enabled watches” , and that one has been up like since the days when Ambit3/Traverse support was first introduced in Suunto App betas, three years ago. I personally don’t see that happening, in about a month when Movescount gets taken down, whole digital transition thing will be marked as finished.