Battery drain after update 2.44.46 (2025 Q3) on Vertical Watch

safari

@ggrego Hello,
Since altitude is barometric, I use “automatic altitude change” before starting each exercise. It does this via GPS.
This way, it provides more accurate altitude information. At least it’s consistent with the “altimeter” app I use on my phone.

bu arada “FusedAlti” de çok işe yarıyor

from the document:

Altimeter

Suunto Vertical uses barometric pressure to measure altitude. To get accurate readings, you need to define an altitude reference point. This can be your current elevation if you know the exact value. Alternatively, you can use FusedAlti (see FusedAlti) to set your reference point automatically.

Set your reference point from the settings under Alti & baro.

ggrego

@safari Ok thank you for the information

Sergei Ladeishchikov

This morning I charged my SV, almost at the end of charging the watch said that the maps were loaded (but I did not load the maps), reset the notifications, seemed to have reconnected the charger and charged the watch to 100%. After 10 hours of inactivity (daily HR, notifications, gesture backlight on) the battery charge was 95%. This was definitely not the case with the previous software. After a full charge, I did not reboot the watch. There is clearly something wrong with the battery discharge. Another note, I have a feeling that the increased discharge is only without activity, during activity the discharge is 2-3% per hour (it was like that before).

dulko79

I charged SVT one day before the update, I believe software release was on Friday, 22.08. Now I have 13 % of battery. Since then I did around 16 hours of GPS activities: walking and cycling with and without chest strap. I have enabled sleep and hrv tracking, notifications and blood oxygen are off. I find battery duration for my needs perfect.

sky-runner

Here is the issue I see with multiple HR sensors every single time I want to switch from one sensor to another.

I start a run. It doesn’t show HR sensor connected because I wear another one - not the one I used previous time in the same activity type
I go to the Exercise Options --> Sensor Data and select the sensor I want to use, select Connect. The sensor gets connected.
However when I exit the Exercise Options menu I see on the top of the activity start screen is that it has already locked to the optical HR sensor and doesn’t actually use the sensor.

It sometimes takes me several attempts of exiting the activity and restarting to make it actually use the sensor I want.

The reason I have two sensors is that one of them is chest HR sensor for shorter runs and another is Coros armband HR sensor for longer runs. The latter is far more comfortable, especially when running with a pack.

timecode

@sky-runner today I went on a run with my wife. We both have Suunto watches, we both have Coros HRMs, we both had issues to get them to work. I had for example had it paired, it didn’t connect. I tried multiple things, selecting it in the activity menu as source, nothing. I had to delete/unpair the second HR monitor I had paired with the watch and only then I was somehow able to get it to work. I spend like 15 minutes before my run fiddling with it and was super annoyed. My wife lost patience and has left it in the car… This was a test of my patience today. I am fed up, really.

Miroslava

@timecode this problem i have too. But only if i have too sensors polar 10 a d coros. I solve it now i use only coros and polar h10 remove from the watch

sky-runner

@timecode said in Battery drain after update 2.44.46 (2025 Q3) on Vertical Watch:

We both have Suunto watches, we both have Coros HRMs

I wanted to emphasize that the problem is not with the Coros HRM. I was using only Coros HRM for months before with zero issues. I didn’t bother switching HRMs before because it was too annoying to unpair and pair sensor, but now with this “improvement” it doesn’t really work either. The only improvement, really, is that I can see the Coros HRM battery level.

timecode

@sky-runner @Miroslava yes it’s independent of the brand and type itself. It’s a general issue.

gone troppo

@Sergei-Ladeishchikov

Yep during activity the battery remain is still like it use to be it’s just during the day night when the battery consumption has increased significantly

Carmak

I think battery consumption has increased since the update on my Race too. It use to be 5% now it’s more like 12% per day without activity recording.

Brad_Olwin

@sky-runner Start a dedicated thread with this. Clearly there are issues although with my sensors I have not had this problem. I think a dedicated thread will help with fixes.

gone troppo

My suunto vertical went through another 10% battery in last 24 hours with no activity recorded from 65-55% will try hard reset today

sartoric

@gone-troppo
just let it discharge fully (battery icon) then recharge.
maybe it just need to calibrate

gone troppo

@sartoric said in Battery drain after update 2.44.46 (2025 Q3) on Vertical Watch:

@gone-troppo
just let it discharge fully (battery icon) then recharge.
maybe it just need to calibrate

Already tried that didn’t work. Have tried every single thing I have seen recommended on this forum and on the fb groups nothing has worked so I just did hard reset as last resort what a pain.

fedequei

Hello,

I have noticed as well a significant reduction in the battery life of my Suunto Vertical between April and today. This happened without any changes to my watch settings (notifications off, daily HR on).
While previously the battery could last much longer: fully charged the 16/4 was 70% the 23/4 (8 days).
Now full charged the 04/09 today is already 74% (4 days).

sartoric

@gone-troppo
just remember that after the hard reset a calibration is basically needed

I’m at 51% after 10 days, and I have increased training time (GPS) in the last weeks, so it looks pretty ok to me.
I usually charge it after 20/21 days when it gets to 15/20 %

JonasLarsson

To summarize: 50 % has problem, 50 % don’t.

Mff73

@JonasLarsson said in Battery drain after update 2.44.46 (2025 Q3) on Vertical Watch:

To summarize: 50 % has problem, 50 % don’t.

So, it is not a bug. It is a half-bug.

JonasLarsson

@Mff73 said in Battery drain after update 2.44.46 (2025 Q3) on Vertical Watch:

@JonasLarsson said in Battery drain after update 2.44.46 (2025 Q3) on Vertical Watch:

To summarize: 50 % has problem, 50 % don’t.

So, it is not a bug. It is a half-bug.

Half-bug, half-feature.