Software release 2.30.26
-
@seanvk Yes
-
@renton82 yes
-
@seanvk said in Software release 2.30.26:
The widget order is fixed
Not fixed, you can sort the widgets by dragging and dropping them in SA.
-
@Jugger said in Software release 2.30.26:
@v-sacre Hold lower button to get to Control panel, you find it there.
Thx for this hint! Now I can reduce one more down widgets.
-
@westie thanks! @Dimitrios-Kanellopoulos any clue on when this might come for the 9PP? I was perhaps under the wrong impression that both SV and 9PP would get the update at the same time.
-
It’s Friday morning here in Australia still no updates for my vertical ?
-
@gone-troppo as always, all updates are phased.
-
Thanks mate so how do we know when the update is ready does something pop up on the watch or app? Or is there something I have to do manually to trigger it ?
-
@gone-troppo you’ll see the update in SA (option wheel on the sync screen)
When it’s uploaded in your watch you’ll find it in settings/general/update. If you have activated auto update, and if you don’t launch it manually, it should be installed at night if you have enough battery -
Installed the update this afternoon… seems to be everything ok… feels smooth. I did my first run this evening, maps are working, I had no problems. The new UI is little bit different, but I think after same days it will be cool. Until now I can say it‘s a improvement 🤩
-
@altcmd It will come. We were working hard on it. I don’t think I can provide you with an exact date but it should be soonish.
-
Hi everyone, I downloaded the software update to my vertical titanium, and after tapping on it to start the install and a countdown to 0 the watch is now completely dead. It doesn’t react even to a soft reset. (Before starting the update the battery was at 75%)
Any ideas on what could I do?
Thanks -
@Tieutieu said in Software release 2.30.26:
I’ll try to delete and set again my walk mode.
Did it work out for you? I still have the issue. Even after I created a new custom sport profile
-
My watch has been stuck in “The device is being restored to a safe state” loop for the past 6 hours after trying to update - has this happened to anyone else?
-
@surfboomerang nope, it didn’t worked for me too.
That’s strange my custom hike is ok, I can unpin ohr, but walk still not even after having recreated it. My climbing custom is also concerned, can’t unpin ohr. -
@Tieutieu is there an Option to downgrade back to the older Firmware!? When yes how to do this?
-
@GiPFELKiND said in Software release 2.30.26:
@Tieutieu is there an Option to downgrade back to the older Firmware!? When yes how to do this?
I don’t know and don’t need it. The new firmware seem quite ok to me !
But maybe it is possible somehow -
@Dimitrios-Kanellopoulos said in Software release 2.30.26:
WHR FW update
This was a nice surprise and seems to have made a noticeable difference in the daily HR readings I’m seeing (only one day in). Previously, my HR always measured somewhere near 100 bpm every time I looked at it, resting or not, as though 100 were the default while it looked for an actual reading. Today, I’ve observed some reasonable numbers. Anyone else?
-
After the update failed, I ended up doing a soft reset and that seemed to fully reset the watch (lost all historical data on the watch, which is a bummer, but oh well - at least it works now). Now it’s saying in the Suunto App that the new software package (2.30) has been downloaded, but the watch is saying it’s up-to-date (with 2.25). Tried hard resetting the watching, forgetting it in the app - nothing seemed to solve it.
-
First night with the new FW.
Sleep tracking seems pretty more accurate, and also ressources gain is completely changed (previously I never recovered up to 100%)
13 nights left for vfc tracking to goes on !(For now the only thing I found strange is way multiple alarms works (I don’t need it but went to have a look) : you can’t select the days you want it, only « everyday/week/one »)