Suunto 9 different ascension depending of sport mode
-
@alexandre-Dutil
Consider that, since your watch rely on GPS data for altitude evaluation, bad signals can affect measurement.To be sure that the issue is due to the sport mode, you should have 2 watches recording the same activity (at the same time) using 2 different sport modes … of course, easier said than done
Do you have always the same results ?
I understand that the accuracy is approximately 7m
In fact 7m is the non baro threshold to recognize altitude modification
For baro watches the threshold is 3m -
To answer your question, yes I do always get the same results. So in a way, my watch is really consistent by sport mode but not between sport mode (default sport mode by the way).
-
@alexandre-Dutil
Btw, 7m recorded for a flat run is normal, right ? even 20m for the same run could be considered as correct (with a non baro device).
Btw2, you can’t calculate that if for 5km those two modes have such a difference, thus for 30km it will be mutliplicated. You may just be in the GPS altitude mesurement precision (non precision).
Btw3, strange that you say it is consistent each time you change sport mode, such a difference happen : either no luck the “bad” gps days are always during snow mode, or something behind it.Have you ever try to do the same day, the same loop twice, switching from one mode to another and see ?
If you sync with SA, and have an Android phone, you can import the raw files to QS and we may see all raw data to check GPS accurency during your activities.
-
Hi all,
I’d like to ask you about huge different between ascent and descent on my couple exercise. Today I ran on almost the same rout and I had absolutely strange data if I compare it to other similar rout.This is that wrong route:
https://www.suunto.com/move/tomaszbury250/5ec805690a7a8664d877e477And here is normal one:
https://www.suunto.com/move/tomaszbury250/5ec577f4a5df69425dde75dd
And here another normal with almost the same route
https://www.suunto.com/move/tomaszbury250/5ea9bf8296c5af7bc79a8831 -
@tomahawk5000 was a storm approaching? Otherwise it was probably something on your sensor, like a sleeve, generating the pressure changes. I think @TELE-HO is the expert in this field
-
@isazi thanks for your reply.
No storm, anything different Vs other trains was that I didn’t use polar h7 to HR measure and I had watch on the inside of the wrist but I change it somewhere in the middle of training but wrong ascent was from the beginning -
@tomahawk5000
the alti graph in your first link looks quite jumpy compared to the others.
I have experienced weird total ascent when the skin covers the sensor venting holes. If it happens once or twice it could be easily already around 20-30m or more.
I saw a much more detailed graph in quantified-self.io. If you upload your wrong recording to QS, you will see unusual spikes and and how much they spike up and down.
would be interesting to see a screenshot of this graph
here’s a graph of one of my recent home TRX workouts.
-
@TELE-HO thank you very much for your help. Please find below link to this wrong exercise:
https://quantified-self.io/user/q46jv01Oz5c5yIUovD5Llcb884J2/event/3cPQA91MbTn2CvY9o8CCsdR6vZmBtcAUZrp4s8xQqWdbYCnand below correct one if needed (it’s almost the same track):
https://quantified-self.io/user/q46jv01Oz5c5yIUovD5Llcb884J2/event/3cPQA91MbTn2CvY9o7eo5xG7AgaYJZHmKUU7EBoKKJCkqNgDifferent between those tracks is only that I used Polar H7 HR monitor on correct track and I had watch on the inside of the wrist on wrong track (I saw that once I use Polar H7 then I have much lower HR bpm which is in my opiniom better)
ps below is link to different track which I did today on bike:
https://quantified-self.io/user/q46jv01Oz5c5yIUovD5Llcb884J2/event/3cPQA91MbTn2CvY9o8CGUtsZ4DDWceDSGHAoytvsMXcyb8f -
@tomahawk5000
the first link shows a smooth alti graph and after a short time it starts becoming spiky, also your bike ride has a downspike that might not be there on the real topography.
I don’t think it is related to the HR belt. If there is a relation then it is the way you wear the watch when you measure with OHR on your wrist.
Next time you do an activity, try to observe if you cover the baro sensor.
And just in case to exclude another potential failure cause: soak your watch over night in water and carefully rinse the baro sensor then.
This helped some athletes already to get their weird measurements fixed
-
Thank you so much for help. I’ll put my watch into the water for all night just in case (hope it will not broke my watch)
