Software Update 2.44.52 (2025 Q3 - HOTFIX)

Stefano M64

@SamuelP said in Software Update 2.44.52 (2025 Q3 - HOTFIX):

especially HRV affects the sleep quality the most

or maybe is the sleep quality that affects the HRV? likely they affect each other …

maszop

Well, HRV indicates, among other things, that you had a bad night’s sleep for some reason. These numbers don’t come from a random number generator.

ajjvbeek

Ever since I updated to this firmware version (2.44.52) I receive ‘stand up’ notifications while not wearing the watch. The watch is in a drawer when it gives the alert.

How does it know I’m sitting down when I’m not wearing it?

safari

@ajjvbeek
It also beeps in my bed at night while I’m sleeping, and I wake up a lot. I think it has something to do with the motion sensor.

Antoine

@safari said in Software Update 2.44.52 (2025 Q3 - HOTFIX):

@ajjvbeek
It also beeps in my bed at night while I’m sleeping, and I wake up a lot. I think it has something to do with the motion sensor.

Same for me. It beeps while i am not doing an activity. (It disappears on soft reset). It seems to be the same beep as one when connecting to HR (arm) sensor. Perhaps it tries to connect all the tiimes and could explain the battery drain in some cases…@Dimitrios-Kanellopoulos

pilleus

@Antoine said in Software Update 2.44.52 (2025 Q3 - HOTFIX):

It seems to be the same beep as one when connecting to HR (arm) sensor. Perhaps it tries to connect all the tiimes and could explain the battery drain in some cases

After the update I recognised that the SV 1 tried to connect to a hr sensor despite whether a sensor was paired/connected nor the ohr was enabled (if I started any activity). This could not be avoided even through a hard reset of the watch.

So you may be right with your opinion.

Wilson75

This is the third time I’ve noticed this issue my Vertical 1 isn’t charging.

Whenever connect my watch to the charger, the screen just shows “downloading map.” assume it’s properly connected to the charger. Not sure if this is related to the recent update. Has anyone else experienced something similar?

maszop

@Wilson75 I noticed this too.
Not only is the cable itself very flimsy and requires constant checking to see if it’s actually charging, but now there’s another level of crap going on – the software suggests charging, but it doesn’t.

Wilson75

Thanks for confirming. I hope it will be fixed because this is very big problem.

To illustrate my issue
I can see charging icone :

Few minutes later still charging … still at 11%

SirMcKey

@Wilson75
Dear Wilson75,
I had the same problem until I cleaned the Contacts of the V1 and the (very cheap designed) charging cradle. All contacts seem to be pretty clean, the watch showed the same as yours, but no juice from the cradle. After using warm water with some liquid soap the problem was gone. Since then the watch and cradle behave well as they should. Maybe it helps, good luck!
K.

maszop

@Wilson75 I sometimes have the same problem, sometimes even worse, because the entire dedicated loading screen is displayed, but the percentages do not change - that is, despite the screen clearly suggesting charging.

@SirMcKey Thanks for suggesting that.

Wilson75

@SirMcKey thanks I will try it out

@maszop same for me with the dedicated charging screen. I will cleaning up+ soft reset of the watch

Antoine

@Wilson75 said in Software Update 2.44.52 (2025 Q3 - HOTFIX):

Thanks for confirming. I hope it will be fixed because this is very big problem.

To illustrate my issue
I can see charging icone :

Few minutes later still charging … still at 11%

@Wilson75 said in Software Update 2.44.52 (2025 Q3 - HOTFIX):

Thanks for confirming. I hope it will be fixed because this is very big problem.

To illustrate my issue
I can see charging icone :

Few minutes later still charging … still at 11%

@Wilson75 said in Software Update 2.44.52 (2025 Q3 - HOTFIX):

Thanks for confirming. I hope it will be fixed because this is very big problem.

To illustrate my issue
I can see charging icone :

Few minutes later still charging … still at 11%

I have had this issue too few days ago with last firmware.

Stefan Kersting

@Antoine can confirm that I have experienced something similar