SOFTWARE UPDATE 2.33.12 - Q1 2024
-
@Dimitrios-Kanellopoulos said in SOFTWARE UPDATE 2.33.12 - Q1 2024:
“Map ruler” tool to measure the distance in a straight line to any location on the map (VERTICAL and RACE)
Map ruler is very interesting feature. It could be an intermediary stage to Pin a POI and routing directly from the watch…
-
-
Hello!
To start with, I’ve been using the S Race for a month now. As far as I’m concerned, nothing was bothering me or causing me any problems before the update (but it all depends on how you use it). I often go out for very long trail rides in performance mode, disabling the Always On screen.
I found the watch extremely responsive before, and never had any problems with the screen being legible when I raised my wrist during a race.
Since the update, it’s become very random. Most of the time, the screen isn’t very bright (the display looks like it did just before switching off) and it’s very difficult to read.
From time to time the problem is solved and then it starts again. I’ve never had that before.
The settings have also remained the same…
I don’t know if it’s related to the update or if I was just lucky before, but it’s still suspicious that this only happened after the update.
Thanks -
@ODo67
I was using similar words for my reports.
it is known to Suunto and I think it needs improvement. let’s hope it gets fixed, soon -
@freeheeler sorry and thanks!
-
In the next update S. Race, how about leaving the option to choose the backlight of the screen when choosing cycling: off, weak, strong. Or start cooperating with companies like Wahoo, Sigma… and bring the possibility of synchronizing third-party devices with the Suunto app.
-
fyi issue is still there
-
deleted
-
It seems that the watch no longer remembers navigation settings and it’s forcing breadcrumbs for each activity, even if it was previously switched off.
I find it a regression but I’m also prepared to hear that it’s actually a feature.
I prefer to have breadcrumbs off when not using routes as it’s just another screen to cycle through and also - it always triggers the best GNSS mode, so I prefer to have it off when not needed.
-
I scanned the previous posts, but didn’t see anyone else with this issue. I have a SV solar Ti. After the update was installed, I was presented with a debug screen, which unfortunately I did not take a photo of. I needed to hold the upper right button to do a reboot. After that, the watch needed to be re-paired with the phone and reconfigured.
Since then, it seems to be working normally. But the screen was a bit disconcerting when shown right after a firmware update…
-
Updated today with some error.
Update started good, so i let it, come back ten minutes later to find all black screen i pick it up, push middle button, and it entered service mode which said update error and gave me option to hold top button for 12 sec. I turned it on (actually updated to latest FW), went through initial menu (as if i am starting it for first time ever). Had trouble connecting it to my phone.
Once i connected it, there were no HRV data, or sleep data, or advanced intensity zones as i set them.
Is it normal to reset these things after the update?
-
@mraka this sounds like what I experienced and posted about earlier today. Note that I had to repair with my phone afterwards. I’m running android.
-
@DrSilverthorn What do you mean repair with your phone?
-
After Update by Outdoor swimming the heart rate graph totally wrong. All zone 1 but heart rate was higher. Wrong shown with wrong colors
-
@sartoric said in SOFTWARE UPDATE 2.33.12 - Q1 2024:
Not sure if this was already reported (can’t find with search) but I’ve noticed it again yesterday (and still there after the update) a bug with multiple apps enabled for an activity.
The switch is always “off” even if the App is selected
Could it be the aero decoupling one or just the first one in the list ? The other seems to work as expectedEDIT: Just tested removing aero dec. and found It’s the first of the list
Regarding this issue, it seems that the problem is the initialization of the list, because in fact if you scroll it down and then go back on top, the switch is correctly refreshed and shows the correct status
-
-
DELETED!
-
@gizmo
very general comment… this isn’t helpful at all, please specify -
@mraka Go into Suunto App, click on watch icon at top, scroll down to manage connection and click. Then tap forget. Then follow almost same process except select “Pair another device”. You may also just be able to use the “Pair another device”, I think it will overwrite the old pairing, but am not 100% sure.
-
@Łukasz-Szmigiel
Yep, I commented on this a while back…@MiniForklift said in SOFTWARE UPDATE 2.33.12 - Q1 2024:
One thing I’ve noticed is that I now have to turn the Navigation to Off before I start an activity, looks like it always reverts back to breadcrumb which it didn’t do before. I don’t really want or need that screen unless I have uploaded a map to use. I thought it would have just defaulted to whatever you had it set it for the last activity, but oh well
I feel the same as you, would like to see it back to how it was before the update
-
@Łukasz-Szmigiel I had reported it as well and I agree with you
-