-
@cosmecosta said in S9 and HR belt:
BTW @wakarimasen @isazi , a little bit of topic, but how is the battery life in your OH1? mine is lasting only around 5/6 hours and I’m thinking on contacting support.
Too short if is not very old.
Tu comunidad Suunto en Telegram: https://t.me/suuntocommunity (spanish)
-
@cosmecosta said in S9 and HR belt:
BTW @wakarimasen @isazi , a little bit of topic, but how is the battery life in your OH1? mine is lasting only around 5/6 hours and I’m thinking on contacting support.
I am not using it for very long activities, lately it has become my travel companion when I want to bring something compact in a trip. But I can do two back to back days with 4/5 hours if I remember correctly.
-
@bulkan said in S9 and HR belt:
@cosmecosta said in S9 and HR belt:
BTW @wakarimasen @isazi , a little bit of topic, but how is the battery life in your OH1? mine is lasting only around 5/6 hours and I’m thinking on contacting support.
Too short if is not very old.
Thanks @bulkan, it has less than a year, 11 months only. Definitely I will contact Polar support.
-
@cosmecosta Before you do, check that you have the latest firmware installed via Polar Flow or Polar Beat. You might also try to disable ANT+, maybe that helps a bit. Mine is ~ 14 months old and the battery can last 9+ hours.
SV: fingers crossed :D
S9 (non-baro): died after 2 months, replaced, holding strong since 03/20
Spartan Trainer: casing broke after 23 months, repaired, lost watertightness 5 months later, died
Despite some pretty bad luck, I still love Suunto! -
@cosmecosta I thought switching off the WHR might save a little battery life - I’m all about charging infrequently.
SO far as the OH1 is concerned, I used it on Sunday when fielding in a cricket game for 3 hours, and Polar Beat still says that the battery is ‘full!’
Based on past experience, I would say it normally lasts longer than 5-6 hours, and I bought it 2019.
Best regards,
RoyM -
@inkognito Thanks,
I’m in the last FW, but I had ANT activated, I’ve just disabled it and I’ll see how the battery performs, if continues the same I’ll contact support.
Thanks to everybody.
-
@cosmecosta Just to let you know: I have both enabled. In fact I used the OH1 connected to a Garmin Fenix 3 HR (using Ant) and also to the Polar Beat app during one gym session, just to see what would happen!
-
@wakarimasen thanks, I just charged it and I’m going to do a cycle to see how much time it lasts.
-
@cosmecosta I use Polar H10, and I discovered some time ago, that it was connected to the watch ones the workout is completed, so I always remove the sensor from the band (when I finish the activities) to ensure this disconnection and battery waste.
BR
Suunto: Race, S9Peak, Spartan Sport Wrist
Garmin: FR745, Edge 530
SA topics:- Guides - https://forum.suunto.com/tags/guides
-
@suzzlo it might be because electrodes are still moist? I think belts use this as an activation trigger.
-
@дима-мельниченко I noticed that a brand new Suunto Smart Belt used to connect easily. Over time the belt has become “less sensititive” in a way. This behaviour made me think that there might have been some conductive substance on the electrodes and now it has worn off. Now I have to concentrate and make sure that my skin under the plastic pad kind of electrodes is really wet. Otherwise I get funny readings or gaps in the recorded heart rate.
Compasses: M-311, A-10, SK-7
Diving: Finnlight Navy 90, Vyper
Sports: Metron, S7, S9B and Vertical -
@brunoh I don’t have a suunto belt, but rather a decathlon one. A year of service didn’t impact the connection speed or readings quality. (other then an issue I think is on s9 fw side)
Belts are somewhat washable, aren’t they? Maybe worth a try. Also you could maybe try to replace just the belt part.
-
@brunoh said in S9 and HR belt:
@дима-мельниченко I noticed that a brand new Suunto Smart Belt used to connect easily. Over time the belt has become “less sensititive” in a way. This behaviour made me think that there might have been some conductive substance on the electrodes and now it has worn off. Now I have to concentrate and make sure that my skin under the plastic pad kind of electrodes is really wet. Otherwise I get funny readings or gaps in the recorded heart rate.
If your belt, doesn’t have the movesense logo background in whitish or light grey it is the old model and this belt is quite faulty, bad readings and so on. You have been very lucky if it has lasted more than 6 months. The newer model, in theory, doesn’t have issues. As @дима-мельниченко says belts are washable, I used to wash my Suunto one every 3/4 weeks and the same for my Polar H10 (only used for biking, for running I’m using the Polar OH1)
-
@cosmecosta Well, I have the text “Movesense” and triangle logo made of dots in both the sensor unit battery cover and in the belt between the contacts. I guess I should be OK then.
-
@brunoh said in S9 and HR belt:
@cosmecosta Well, I have the text “Movesense” and triangle logo made of dots in both the sensor unit battery cover and in the belt between the contacts. I guess I should be OK then.
I mean, in the belt, where there is the logo Movesense, if the background of the letters is black, the belt is the old model and tend to be faulty, if the background is white or light grey is the newer model. If you have the old one, you can contact support about the bad readings and they probably will exchange it for the new one.
In my experience, with the old model, you can wash it and will work ok for one week or so and then will start to fail again. Yo can search in the forum for threads talking about the Smart Belt Issues.
-
Just to keep my promise of informing you the Garmin HRM Pro connected flawlessly to the s9b and the HR was spot on. I even had my fitness (vo2) jump 4 units
